A washing machine is among the essential appliances that you use in your daily life. It makes washing your clothes easy. But if the washing machine’s drum is loose and makes noise during the spinning, it can get annoying.

A worn drum, an unleveled washing machine, an overloaded drum, or a broken rear drum might be the reasons behind a loose drum in your washer. To fix these problems, check the inner and outer parts of your washing machine to find the exact reason for the loose drum, and fix the issue accordingly.

In this article, I will explain the exact reasons and fixes for loose drum problems in a washing machine. So, keep reading.

Why is my washer drum loose?

These are some reasons why a washing machine drum might be loose.

1. Worn dampening straps

The dampening straps hold the tub inside the washing machine.

The 4 dampening straps are located in 4 corners of the washing and help reduce the drum’s vibration due to spinning.

If any of the 4 straps are worn out or damaged, the drum will loosen up, and you have to replace all four.

2. Damaged suspension springs

The suspension springs hold the washing machine’s outer tub when loaded with clothes.

They are located at the base of the top-loaded washing machine and the top or the side frame of the front-loaded washing machine.

If they are worn, or one of the springs is damaged, you should replace all the springs to avoid losing the washing machine drum.

3. Damaged shock absorbers

The shock absorber is located between the outer tab and the base frame.

The drum has two tubs, outer and inner.

The outer tub secures the inner tab, and the inner tab helps in washing the clothes.

The base frame is located behind the washing machine.

It holds the gearbox and motor.

The shock absorber helps move the inner drum smoothly, but if the drum is losing and making a loud noise, there might be problems with the shock absorbers.

4. Broken drum bearings

Drum bearings are small metal rings that help to spin the drum.

It is located behind the drum of a front-loaded drum and the bottom of the top-loaded drum.

But for long uses, the bearings can wear out or be broken.

And this can cause a loose drum.

5. The washing machine isn’t level

Sometimes, an unleveled or unbalanced washing machine can cause a loose drum issue in the washing machine.

If the washing machine isn’t leveled according to the surface or the locknuts on the base of the legs, the drum will get loose.

6. The drum screw is loose

The drum of the washing machine is held by some screws.

And you can access the screws from the back side of the washing machine.

If the screws aren’t tightened up, the drum can be loose and make loud noise during spinning.

6 ways to fix loose drum in a washing machine

Here is how you can fix the loose drum.

1. Replace worn dampening straps

If the dampening straps of your washing machine are worn out, you should replace them with new dampening straps.

To do that, you have to follow the below directions:

• The first step is disconnecting your washing machine’s power and water supply.
• Now, unscrew the control panel.
• Once the screws are removed, move the control panel slightly forward and slide it sideways to the left.
• Now disconnect the panel wire harness and the clips on the wire harness.
• Once it is done, take a couple of spring clips that are 3 inches in size and depress them in the top space of the front panel. Now pull out the front panel and take it aside.
• Now you find two screws that secure the top of the washing machine cabinet, unscrew them using a quarter screwdriver.
• Slide the top of the cabinet forward, gently lift it and set it aside.
• Now, look through the top of the cabinet. You can find 4 dampening straps on 4 each corner. To replace one of the dampening straps, you must replace all 4 dampening straps.
• Take a hex-inch head screwdriver, remove the screw that holds the dampening strap to the tub, and lift the strap off. Also, unscrew the screw attached to the cabinet mount near the cabinet wall.
• Now remove the old strap from the tub and put the new dampening strap in the black cabinet mount. Make sure it is seated fully, then lock the tab into the cabinet through a rectangular slot. Push it up, tilt it into place, and hold and screw it. Make sure you don’t over-tighten it. And now, do the same with all 4 dampening straps.
• Finally, reinstall all the parts.

2. Replace the suspension spring

If your washing machine is balanced, but the drum inside the washing machine is shaking, there must be an issue with the suspension springs.

In this case, you should replace the suspension spring.

Before replacing the suspension spring, you have to access it.

• To access the suspension spring, you must remove the washing machine’s front panel because the springs are located behind it.
• We have to tip back the top panel assembly to remove the front panel.
• Before lifting the top, use a piece of tape to prevent the lid from opening.
• Now use a putty knife to press in and release the clip that holds the top panel in place and do the same for the other side.
• Now you can tip back to the top.
• Now, look through the top inside the machine.
• You can find two screws that hold the top panel. You have to loosen and remove these screws.
• Use a screwdriver to loosen up and remove the two screws.
• Once the screws are removed, tilt the front panel forward and lift it. And that’s the way you can remove it from the washing machine. Now take it aside.
• Once the front panel is removed, you can see the six suspension springs at the machine’s base.
• Now remove the springs. To do so, use a pair of locking pliers, simply grab on the springs, lock it in place, and now pull up, and that’s how you can take the spring out of its mounting.
• Then you need to rotate the spring slightly from the bottom, and you can pull it out of its mouth.
• To install the new spring, add a dab of grease to the bottom of the spring, install it in the cabinet or the mouth hole, and rotate it around until the ends come out.
• After it, use a pair of locking pliers to grab onto the spring, then carefully pull it up and put it in position.
• Now reinstall the front panel, the top panel, and all the other parts.

3. Replace the shock absorbers

The shock absorbers help the inner drum move smoothly.

But if the drum is loosened up, you must check the shock absorbers once. 

And if you see the shock absorber or absorbers damaged, you must replace them.

To replace the shock absorber, you can follow the steps:

• Disconnect the wire from the main and the hoses.
• Take two blocks and place them under the washing machine. To do that, you must tilt its backside.
• Take a nut driver and remove the bottom access panel by simply unscrewing the screws.
• Begin with the two outside ones first, then remove the center one last. You need to maintain the machine when removing the screws.
• Let the access panel drop, pull it away, and set it aside.
• Now you can access both front shock absorbers. They are attached to the base of the machine with a locking pin. The locking pin has a little lock tab on the side of it.
• To retract the locking tab first, you must press it in and tap the pin completely out of its socket.
• At the top portion of the shock absorber, you can find a little arrowhead fastening the twists into an opening in the bottom of the tub. Turn it 90 degrees by using a wrench and drop them out of the tub.
• Now reach into the access panel and depress the locking tab on the pin.
• Now remove the pins from the base brackets by using pliers and adjust them so you can catch one jaw with the pliers against the end of the pin and the opposite jaw against the mounting bracket on the bottom of the washing machine. Or you can use a large flat-blade screwdriver and get it in behind the head of the pin and depress the locking tab simultaneously.
• Once the pin is started to move, grasp it with the pliers and pull it out. Now discard the original pin.
• Once it is done, pull out the base of the shock absorbers of the bracket and turn the upper portion 90 degrees by using a wrench until it pops out of the opening.
• Now remove the old shock absorbers.
• To install the new shock absorber, position it on top, put the arrowhead opening, and then turn it 90 degrees clockwise.
• Now take the pin and push it into the opening till it lines it up. You can push it by hand.
• Do the same procedure on the right side of the base to replace another shock absorber.
• Now reinstall all the parts and structure it completely.

This completes the replacement procedure.

4. Replace the worn bearings

If the drum of the washing machine loses up, then the bearings must have a problem.

If the bearings are damaged or worn out from long use, you should replace them with new ones.

To replace the bearings, you need to follow these steps:

• Before starting anything, disconnect the washing machine from the mains and switch off the hoses.
• After disconnecting the machine, unscrew and remove the lid.
• Remove the soap drawer and disconnect the hoses on the back of the draw housing.
• Then lift the housing and move it out of the way.
• Next, remove the retaining spring holding the door seal to the front panel.
• Now remove the control panel and bottom access panel.
• Now remove the front panel by unscrewing it. To do that, you must also disconnect the door lock from the inside.
• Now check the bottom of the washing machine and disconnect the pressure chamber and hose from underneath the tub.
• Then check any other pipes connected to the front tub and disconnect them.
• Next, unscrew and remove the rear panel back side of the machine.
• Remove and disconnect the drum motor. If your machine is not a direct drive machine, remove the pulley and belt.
• Now disconnect all the electric connections. And also, check around the drum if you find any other connections and disconnect them.
• Take off any removal weights fitted to the tub. These can also be located at the bottom of the back.
• Remove the dumper pins connected to the dumper and pull them out. If the damper can be removed, disconnect the dumper at the other end.
• Remove the spring from the top of the cabinet and lift the drum out.
• Now place the drum on a mat or the floor. And unscrew all the bolts holding the two tubs of the drum together. If there are any clips, you also need to disconnect them.
• Now separate the two halves.
• Using a soft-face hammer or mallet, tap the end of the drum shaft to release it from the bearings. You may need a socket extension to push it out.
• Remove the heater from the tub so that you can lay the tub down flat.
• Use a screwdriver to pull the seal out of the tub. When the seal is removed, apply the penetrating fluid on the inner bearing to make it easier to remove.
• Turn the tub over and use the soft face hammer and drift to knock the inner bearing out of the tub. Now turn the tub back over to remove the outer bearing.
• After both bearings are removed, clean the housing before knocking on the new bearings.
• Now knock the bearing, and ensure you are applying pressure evenly around the side with a soft face hammer, not at the center until it is fully located.
• Now push the new seal into the bearing housing.
• Now lower the drum of the tub so that the shaft sits into the bearing.
• Then add the two halves correctly and reinstall the drum inside the machine frame. Also, reinstall other parts of the machine and set it properly.

5. Level the washing machine

If your washing machine is shaking when washing the clothes, there might be a leveling problem.

If the washer is not leveled up with the floor or is not set properly, it causes losing the drum.

To fix the issue, you first follow the steps:

• Take a spirit level and check the top of the washing machine to see if it is leveled.
• If the top of the machine is leveled, still your washing machine is shaking, then check the legs of the machine and raise the lower metal or rubber legs.

6. Tighten the drum screws

The loosened drum screws are also liable for a loose drum issue.

To fix the issue, you should tighten the screws.

To tighten the drum screws:

• Remove the rear panel of the washing machine.
• And then, you can get access to all the screws added to the drum.
• Tighten them up and attach the rear panel door.

Final words

These are all possible reasons and fixes for a loose drum washing machine. You just need to check your machine for which problem it is facing and then fix it according to the problem.

If you don’t want to face the problems the second time, you must avoid overloading and heavy weight loading inside the machine.

If you find the fixes difficult or think you cannot fix the washing machine, then you can call an expert. If your washing machine still faces a loose drum issue, you can buy a new one.

Related articles:

• Can You Put Detergent Directly On Clothes? (+The Correct Way)
• Can You Run A Washing Machine With A Generator?
• 5 Common Samsung Washing Machine Error Codes (+Quick Fix)
• 8 Common LG Washer Error Codes (+Quick Fix)

---

Reference: LG Official Guide, Kenmore User manual, GE washer front load user manual, Maytag Front Load Washing Machine Official Troubleshooting Guide.

Bosch washing machines have a common way of communicating faults through error codes. If you want to know the common error codes in your Bosch washing and how to fix them, you are at the right place.

The error code E3 in the Bosch washing machine occurs when the door is not latching properly. You must reset the washing machine or replace the door lock to fix this issue. When water temperature issues arise, it communicates as an E1 error code. Replace the heating element to fix this issue. 

Error codes	Description
E-3	Door lock error
E-1	Heating issue detected
E-2	The drum does not rotate
E-4	Unusual heating issue
E-6	Draining issues

In this article, I will help you understand 5 common error codes of the Bosch washing machine and the steps to fix the errors. So, keep reading.

What are the common Bosch washing machine error codes?

Error codes help you to figure out and fix the issue.

It indicates specific faults in your washing machine, and you can use it to understand how to fix the issues.

1. Error code E3

Error code E3 in the Bosch washing machine communicates that the door is not closing properly.

If there are issues in closing the washer’s door, the washer won’t start.

If the washer is having trouble getting started, it is because the door lock is damaged, and it couldn’t seal the door with the washing machine during the washing cycle.

You can fix this issue yourself if you are familiar with the technical aspect of the washing machine. 

Here are the possible causes of the E3 error code in the Bosch washing machine:

• Loose wire connections
• A faulty door lock
• Control board issues

Follow the steps to fix the problem.

Reset the washing machine’s control panel.

The control panel is the multifunctional mini-computer in the washing machine, which consists of several electrical components.

In the long run, electric components in the control panel may get damaged and cause glitches in the washing machine.

A simple reset can fix the glitches on the control panel and helps to clear the error code. 

You can reset your Bosch washing machine by following the steps below:

• Disconnect the power supply from the washing machine by unplugging the power cord from the electric outlet.
• Let the washer stay disconnected for 5 to 10 minutes.
• Reconnect the power supply to the washer. 

Resetting can reboot the electric components of the washer, clearing most of the control panel glitches.

Replace the faulty door lock

Door latching is an important mechanism that works with the bi-metal strip inside the door lock to keep the door shut while the washing cycle is running. 

The door lock has electric components that pass the signal to latch the door with the washing machine. 

If the door lock is damaged or worn out, you must replace it to bring the washer back to working condition. 

Follow the steps below to replace the door lock in the Bosch washing machine:

• Unplug the washing machine from the electric outlet.
• Open the washer’s door, remove the door seal using a flathead screwdriver, and push the door seal inside the washer.
• Using a screwdriver, push the door lockout and disconnect all the wires to remove the door lock.
• Purchase the new door lock based on the model of your Bosch washer.
• Replace the new door lock and secure it in place. And reconnect all the wires you initially disconnected.
• Reposition the door seal and secure it with the retainer spring.
• Close the washer’s door and plug it into the electric outlet. 

Check if the error code E3 has disappeared.

If not, hire a professional to check and figure out the issue and fit it efficiently. 

2. Error code E1

The E1 error code occurs in the Bosch washer when the desired water temperature is not achieved at a fixed time. 

There is a significant reason behind the temperature issues in the washer. 

Most of the time, temperature issues arise due to faulty heating elements. 

You must measure the resistance of the heating element to check if the heating element is faulty. 

Also, check if the control board is damaged or has issues causing the E1 error code. 

Follow the steps below to fix the E1 error code.

Check the resistance of the heating element.

The first step is to check the resistance of the heating element to find out if the heating element is faulty. 

If the resistance of the heating element is between 38 – 46 ohms, there are no issues in the heating element. 

You must replace the heating element if there is very high or low resistance.

Follow the steps to replace the heating element of the bosch washing machine:

• Unplug the washer from the power supply before beginning the repair to prevent yourself from electric hazards. 
• Move the washer from its original position and place it in a comfortable position to work on the issue.
• Access the top panel of the washer and detach it by removing the screws and securing it with the washing machine.
• Detach the detergent drawer to access the inner parts of the washer.
• Disconnect the control panel from the washing machine by removing the screws attached to it.
• Open the door and remove the door seal by disconnecting the retaining clip from the washing machine.
• Detach the front panel of the Bosch washing machine by removing the screws holding it in place. 
• You can locate the heating element at the bottom of the washing machine’s drum.
• Detach the wires connected to the heating element after taking a digital photo of the wire connections for future reference. 
• Remove the retaining clip holding the heating element in the slot using a screwdriver.
• Pull the heating element out and check for any sign of damage.
• Remove the thermostat from the faulty heating element and replace it with the new one.
• Replace the new heating element in the slot at the bottom of the washer’s drum.
• Secure it with the nut using a screwdriver.
• Reconnect the wires by referring to the photo you took. 
• Reattach the front panel and secure it with the screws.
• Reattach the control panel and secure it with screws.
• Reattach the top panel and secure it with screws.
• Reattach the detergent drawer and move the washing machine to its original place.
• Plug the washing machine into the electric outlet and check if the error code has disappeared. 

3. Error code E2

E2 error code in the Bosch washing machine occurs when its drum is not rotating while you start the washing cycle. 

If the motor is faulty or stops working, it will not let the drum rotate. 

The common fault that decreases the motor’s efficiency is when the motor’s brush is worn out. 

To fix this issue, you must replace the motor brush from your washing machine.

• Unplug the washing machine from the power supply.
• Remove the drain hoses from the water supply pipe. 
• Detach the back panel from the washing machine by removing the screws.
• You can locate the motor at the bottom of the washer’s drum.
• Remove the motor by disconnecting the drive pulley from the drum.
• As a next step, disconnect the wires and earth tag attached to the motor.
• Locate the motor and, using a screwdriver, remove the bolt securing the motor to the washing machine base.
• Disconnect the motor from the washing machine and place it on a solid surface.
• The screws hold the brushes attached to either side of the motor.
• Take a digital photo of how the brushes are connected for future reference.
• Using a screwdriver, disconnect the screws securing the brushes with the motor.
• Prepare the new brush to replace the motor.
• Replace it in the motor by referring to the photo you took.
• Replace the motor at the bottom of the drum and reattach the drive pulley to the drum.
• Reattach the back panel and secure it with the screw.
• Attach the drain hose pipe and secure it with the locking tab using a wrench. 
• Move the washer to its original place and plug it into the electric outlet. 

Switch on the washing machine and check if the error code has disappeared. 

If the error code persists, try resetting the washing machine to clear the control panel glitches causing the E2 error code. 

4. Error code E4

Error code E4 communicated the unusual heating in the washing machine. 

The unexpected heating occurs when there are issues with the temperature sensor of the washing machine. 

If the control panel is faulty, it will also cause the error code E4 in the Bosch washing machine. 

To fix this issue, you must replace the temperature sensor.

If the temperature sensor is faulty, it detects the false temperature, causing the error code E4 in the washing machine. 

A temperature sensor, also known as a thermistor, is attached to the heating element. 

Follow the steps below to replace the temperature sensor:

• Unplug the washing machine from the electric outlet to prevent yourself from electrical hazards.
• Move the washer from the cabinet and place it in a comfortable place to work.
• Remove the top panel of the washer by disconnecting the screws attached to it.
• Access the detergent drawer. Disconnect it from the washer and place it in a safe place.
• Remove the control panel from the washing machine by removing the screws attached to it.
• Open the door and disconnect the retaining clip to remove the door seal from the washer’s door.
• You must remove the front panel to access the temperature sensor.
• Remove the screws attached to the front panel to disconnect it from the washing machine.
• You can locate the heating element at the bottom of the drum.
• You can see wires being connected to the heating element. Consider taking a digital photo of the wire connections for future reference.
• A bolt at the bottom of the drum will secure a heating element. Using a screwdriver, unscrew it and remove the heating element from the slot.
• A temperature sensor will be attached to the heating element. Disconnect it from the heating element.
• Replace the new temperature sensor with the heating element and put it in the slot.
• Secure the heating element with the bolt using a screwdriver.
• Redo the wire connecting using a photo you took.
• Reattach the front panel and secure it with screws.
• Reattach the door seal and secure it with the retaining clip.
• Reattach the control panel and secure it with the screws. 
• Secure the top panel with screws and attach the detergent drawer.
• Plug in the washer and check if the error code E4 has disappeared. 

If the error code persists, there will be issues with the heat relay.

Seek help from a professional to fix the heat relay issues. 

5. Error code E-6

E6 error code in the Bosch washing machine occurs when there are draining issues.

The main causes of draining issues are a clogged drain hose, dirty filter, or drain pump issues. 

Follow the steps below to fix the error code E-6 in the Bosch washing machine.

Unclog the drain hose.

Drain hoses expel the water from the washing machine after the drain cycle.

If the drain hose is clogged, water won’t drain from the washing machine resulting in the E-6 error code. 

Follow the steps to unclog the drain hose:

• Begin by disconnecting the power supply from the washing machine.
• Move the washer to the comfortable place from the cabinet to work comfortably.
• Access the back side of the washing machine. 
• Disconnect the drain hose from the washing machine using a wrench to release the clamps holding it in place. 
• Inspect the drain hose to see the condition of the clog.
• If there is no stubborn clog, you can run the hot water inside the drain hose to remove the dirt and debris deposition.
• If the clog is too stubborn to escape the hot water treatment, you must use a dash of vinegar and baking soda mixture to run through the drain hose. Or you can buy a ready-made drain cleaner to make the cleaning easy.
• Purchase a plumbing snake to insert down the drain hose to remove the clog completely. Turn the plumbing snake clockwise and anticlockwise to remove dirt and debris accumulation.
• Once the drain hose is unclogged, reattach it to the pipeline of the washing machine and move it back to its original place. 
• Plug it on and check if the error code has disappeared. 

If not, continue with the next step.

Clean the filter

The drain filter catches all the dirt and particles from the washing cycle to prevent the drain pump from getting clogged. 

If the filter is clogged with dirt particles, you must clean it using soapy water. 

Locate the drain filter at the base of the washing machine; using a screwdriver, remove the screws, securing them in place. 

Twist it and disconnect it from the washing machine. 

Wash a filter in soapy water and remove the excess dirt using a brush. 

Once you clean it, reattach the filter. 

Check if the error code has disappeared, or consider hiring a professional to see if there are issues with the drain pump.

Final thoughts

Error codes are common figures that indicate the faults in the washing machine. Error codes differ based on the washing machine brand and model. 

It is important to know what the error code indicates to fix the error efficiently. In this article, you can find 5 common error codes and how to fix them by following the step-by-step process. If you can’t fix the error yourself, consider hiring a professional.

Related articles:

• 6 Reasons Your Washing Machine Is Off Balance (+Fix)
• Can You Put Detergent Directly On Clothes? (+The Correct Way)
• Can You Run A Washing Machine With A Generator?
• 5 Common Samsung Washing Machine Error Codes (+Quick Fix)
• 8 Common LG Washer Error Codes (+Quick Fix)

---

Reference: Bosch official troubleshooting guide

Error codes are alphanumeric units to communicate faults in your Samsung washing machine. You are at the right place if you want to know the common error codes and how you can fix them.

The error code ND indicates draining issues in your washer. To fix this, check the drain hose and filter and unclog the drain hose/filter to clear the error code. A TE error code occurs due to heating issues. You can fix this by resetting the washer or replacing the temperature sensor.

Error codes	Description
ND	Water drainage issues.
tE	Temperature sensor issue/Washing machine overheating.
OE	The washer is overfilling/overflowing.
1E	The washer can’t gain water from the hose pipes.
UB	The washer/load is off-balanced.

In this article, you will find steps to fix 5 common Samsung error codes in detail. So, keep reading.

What are the common Samsung washing machine error codes? (+Quick fix)

Modern Samsung washing machine, unlike old models, comes with an advanced display and touch panel to make the operation easy.

It also displays error codes in the control panel to indicate the faults in the washer. 

While error codes help figure out the faults and fix the issues, it will be frustrating to see the error codes while the washing cycle is running.

Isn’t it? 

When an error code appears on the control panel, you don’t want to panic as you can fix it easily, provided you know what a particular error code stands for. 

I have explained the 5 common error codes and the easy steps to fix them. 

Shall we get started? 

1. Error code ND

Error code ND in the Samsung washing machine appears when drainage system issues arise.

Drainage system issues include:

• Blocked drainage filter
• Clogged drain hose
• Drain pump issues

You can fix this issue by following the steps below.

Unclog the drain hose

At the end of the draining cycle, a washer expels the water through the drain hose.

If the drain hose is clogged with dirt and debris, it won’t let the water drain, resulting in the ND error code in the Samsung washer. 

You can fix this issue by unclogging the drain hose. 

Follow the steps below to unclog the drain hose:

• Disconnect the power supply from the washer.
• Move your washer from the wall to access the drain hose at the back of the washer.
• Check if the drain hose is kinked and bent. Straighten it to facilitate easy water flow.
• If the drain hose is completely damaged, you must replace it with a new hose. 
• You can unclog it to fix the issue if it is clogged. You can unclog the drain hose by running the vinegar solution into it. If the clog is stubborn, you can use a metal wire to unclog the drain hose.
• Reattach the drain hose to the washer and pull it back to its original position.
• Plug in your Samsung washer to the electric outlet. 

Switch it on and check if the error code ND has disappeared. If the error code persists, follow the steps below to fix the issue. 

Clean the drain filter

The drain filter catches the dirt particles during the drain cycle to prevent the drain pump from getting clogged.

If the drain filter is accumulated with dirt, it will revert to the water, causing drainage issues. 

Follow the steps below to clean the drain filter:

• Unplug the washer from the electric outlet.
• You can locate the filter at the base of the washer.
• Disconnect the drain hose to remove the filter from the washer. 
• To access the filter, you must open the washer’s door.
• Detach the filter’s cover to see if the filter is accumulated with dirt and debris.
• Twist and turn the filter to remove it from the washer.
• Wash the filter with soapy water and vinegar solution.
• Clean it with a brush to remove all dirt and debris. 
• As the filter is wet, don’t attach it as it is. Dry the filter to remove all the moisture.
• After 10 minutes, reattach the filter and drain hose to the washer.
• Reattach the filter’s cover and secure it in place.
• Plug the washer into the electric outlet and check if the error has disappeared.

If the error code ND is still showing, you must seek help from a professional to check and replace the drain pump.

2. Error code tE

The error code tE occurs in the Samsung washer when heating issues arise.

It usually happens due to the faulty temperature sensor located at the back of the washer. 

To fix this issue, reset the control board of the washer.

Follow the steps below to reset the control board of the Samsung washer: 

• Disconnect the power supply from the washer by unplugging the power cord from the electric outlet.
• Wait for 5 to 10 minutes.
• Plug in the washer to the electric outlet after 10 minutes.
• The Control board has reset successfully. 

Switch on the washer and check if the error code has disappeared.

If it has disappeared, the control panel reset has solved the issue. 

Is the TE error code still displaying in the control panel? 

If yes, you must run the diagnostic mode to check if the temperature sensor is faulty. 

Follow the steps below the run the diagnostic mode in the Samsung washer:

• Locate the signal and extra rinse button in the control panel.
• Press and hold the buttons for 5 seconds.
• Next, hold the extra rinse button to switch on the input mode.
• Resistance if the temperature sensor is displayed on the control board. 

Compare the temperature sensor with the table below.

S.NO	TEMPERATURE	R-MAX	R-MIN
1	-20℃ (-4℉)	494.3KΩ	481.3 KΩ
2	-10℃ (14℉)	279.1KΩ	273.0KΩ
3	0℃ (32℉)	163.8KΩ	160.6KΩ
4	10℃ (50℉)	99.2KΩ	97.5KΩ
5	20℃ (68℉)	61.9KΩ	61.0KΩ
6	30℃ (86℉)	39.8KΩ	39.3KΩ
7	40℃ (104℉)	26.2KΩ	25.9KΩ
8	50℃ (122℉)	17.7KΩ	17.5KΩ
9	60℃ (140℉)	12.2KΩ	12.1KΩ
10	70℃ (158℉)	8.6KΩ	8.5KΩ
11	80℃ (176℉)	6.2KΩ	6.1KΩ
12	90℃ (194℉)	4.5KΩ	4.4KΩ

Follow the steps below to replace the temperature sensor: 

• Begin by unplugging the washer from the electric outlet.
• You can locate the temperature sensor at the bottom of the drum of the washer.
• Remove the back panel by disconnecting the screws holding the panel with the washer.
• You can locate the temperature sensor at the bottom of the drum, secured with 2 screws.
• Using a screwdriver, unscrew the screws holding the temperature sensor in place.
• And a temperature sensor is attached to the wires. Disconnect the wires to remove them completely. Disconnect the temperature sensor and discard it.
• Replace the new temperature sensor and secure it with screws and wires.
• Reattach the back panel and secure it with screws. 
• Plug the washer into the electric outlet and check if the error code tE has disappeared.

3. Error code OE

The OE error code in the Samsung washer indicated the overfilling water issues.

Overfilling in the Samsung washer happens due to the following reason. 

• Control board issues
• Using too much detergent 
• Failure of the water sensor

Follow the steps below to fix the issue:

Reset the control panel to clear the glitches

Before proceeding with serious issues, reset the control panel of the Samsung washing machine.

• Unplug the washer from the electric outlet. 
• Wait for 5 to 10 minutes. 
• Replug the washer with the electric outlet after 10 minutes. 

If the control panel glitches are causing the error code, after a reset, the error code OE will disappear.

Check if you are using too much detergent.

Using low-quality detergent in a highly efficient washer can cause issues with the washer.

If you use excess detergent, suds will be produced, causing the washing machine to overflow. 

The excess suds creates pressure in the pressure switch.

It passes the false overflow signal to the sensor, resulting in the OE error code. 

To fix the issue, initiate the spin mode and let the water drain by pressing the drain button. 

Unload the clothes from the washer and initiate the rinse mode to remove the excess suds settled in the washing machine’s drum. 

Unplug the washer, plug it back, and check if the error code has disappeared.

Check the water sensor for faults.

A water sensor detects when the desired water reaches and stops the water flow.

If the water sensor is faulty, overfilling occurs, and an OE error appears in the control panel. 

Follow the steps below to replace the water sensor:

• Unplug the washer from the electric outlet.
• Move the washer from its original position to access the back panel.
• You can locate the water level sensor on the back side of the washer.
• You need to remove the back cover and rear access panel to access it.
• Using a Phillips screwdriver, remove the Phillips screws securing the back cover. Push the cover to detach it from the washer.
• Tilt the control panel forward by removing two screws holding it in place.
• Disconnect the rear access panel by removing four screws and securing it.
• You can locate the water level sensor tubes at the left upper corner connecting with the sensor at the top. You must release the tubs from the tabs to remove the water sensor.
• Access the water sensor at the top of the washer near the control panel.
• Replace it with the new one and secure the tubes with the tabs.
• Reattach the back cover and rear access panel.
• Plug in the washer and check if the OE error has disappeared. 

4. Error code 1E

1E error code appears in the washer when it can’t gain water from the hose pipes.

If the water doesn’t flow in the washer, it can’t initiate the washing cycle, resulting in the 1E error code. 

The causes of the 1E error codes are a clogged drain hose or the drain hose not fitted with the washer tight.

To fix this issue, you must unclog the drain hose by following the steps mentioned in error code 1. 

Check if the drain hose is loosely connected and leaking water. 

Follow the steps below to tighten the drain hose:

• Unplug the washer from the electric outlet.
• Move it from its original position to access the drain hose.
• Using a wrench, detach the hose and check it for any damages. 
• If it is damaged, replace the drain hose.
• Or else fit it in the water supply line. Tighten it using a wrench.
• Plug in the washer and start the washing cycle.
• If the water flows, the 1E error code will stop showing on display.
• Another cause of this issue is the failure of the water level sensor. Follow the steps mentioned in error code 3 to replace the faulty water level sensor. 

5. Error code UB

The UB error code in the Samsung washer occurs when your washer is in an off-balanced load.

Here are the common causes of the error code UB on the Samsung washer:

• The clothes in the tub are tangled and clumsy. 
• The washer is placed on an unlevelled surface. 
• You have overloaded the washer. 
• You have started the washing cycle with fewer items.  

You can fix this issue by balancing the load and placing the washer on the leveled surface. 

Follow the steps below to fix the issue:

Untangle the clothes

If the washer is stuck amid the washing cycle displaying the error code UB, you must pause the cycle and follow the instructions below. 

Manually untangle the clothes and take out some clothes if you have overloaded the washer. 

As Samsung washing machines are designed to set specific washing cycles based on the fabrics of clothes, you must set the right washing clothes based on the clothes you are loading.

Reset your washing machine

If the error code UB persists after balancing the load, try resetting the washer to clear the glitches in the control panel. 

Unplug the washer from the electric outlet and wait for 5 to 10 minutes. 

Replug it into the electric outlet and check if the error code has disappeared. 

If control panel glitches are causing the error codes, resetting the washer will solve the issue. 

If the error code appears back, you must check if your washer is placed on the leveled surface.

Check the surface where your washer is placed.

If your washer is placed on a bumpy surface, it will become off-balanced, resulting in the UB error code. 

You can fix it by moving the washer to another place or adjusting the washer’s leg. 

You can adjust the washer’s leg using a wrench.

Turn it clockwise to move it down and anticlockwise to move it up.

After adjusting the leg, secure the washer’s leg with the locking nuts. 

If you decide to move your washer to a new location, ensure the surface is not so smooth or slippery. 

After leveling the surface, check if the error UB has disappeared.

Also read: 6 Reasons Your Washing Machine Is Off Balance (+Fix)

Final thoughts

Error codes commonly occur in the washer now and then. So, you don’t have to be scared or worry about the cost of repair. Most of the time, a simple repair can fix the issue, which you can do yourself. 

However, if a complex problem occurs, you must seek a professional’s advice. In the article, I have discussed common Samsung ND, TE, OE, IE, and UB error codes. And also, there are steps to fix the error code. Go through the causes and follow the steps to fix the error codes.

---

Reference: Samsung Official Error Codes.