Recent Posts

8 Common LG Washer Error Codes (+Quick Fix)

Written by Jeniffer Smith in Washing Machine,Appliances 

It is common for a washer to display error codes to communicate its faults and failings. Each error code indicates specific faults. If you use an LG washer and find error codes, you must know what the errors mean to fix the faults.

Error CodeDescription
FEWater is overflowing beyond the marked limit of the tank.
LEThe motor is locked.
OEDraining issues in the washer.
dEThe door is not latched/closed properly.
CLChild lock is activated.
UB/UEThe washer is out of balance.
tEThe thermistor is faulty.
SUDExcessive detergent that hinders the washer’s function.
Table showing common error codes of an LG washer and respective issues

This article will help you understand the common error codes of an LG washer and show ways to fix the error codes. So, keep reading.

What are the common LG washer error codes? (+Quick Fix)

Error codes are displayed in the front panel of the LG washer as two or three letters codes.

Each error code indicates the specific error code in the washer.

If you use an LG washer, you must be aware of all the error codes to fix the issues that arise from time to time. 

Here are 8 common error codes and effective ways to fix them:

1. Error code FE

It can be frustrating if your washer is stuck in the middle of the washing cycle and displays an FE error code.

Read on to learn the causes and possible solutions to this issue in your LG washer.

FE error code appears in the LG washer’s control panel when the water is overflowing beyond the marked limit of the tank.

There are several reasons for the FE error in the LG washer.

Below are some causes of the FE error code in the LG washer and quick fixes.

Malfunctioning water inlet valve

A water inlet valve is located on the back side of your washing machine.

It is designed in a way that it opens and closes to allow the water to flow into the tub of the washer when it receives certain electric signals.

If the water inlet valve is damaged or loses flexibility, it blocks or overfills the washer’s tub.

If it is stuck open, water will start to overflow beyond the limit resulting in the FE error code in your washer.

To fix this issue, you should replace the water inlet valve of your washer.

Using low-quality or wrong detergent

If you use a high-efficiency washing machine, you must use a specially designed detergent.

Using a low-quality detergent will cause damage to your appliance and also reduces the spark of your clothes.

Another common mistake that people make is using too much detergent. 

Using excessive detergent will cause overflow in your washer, resulting in the FE error code. 

To fix this issue, use a specific detergent in the right amount.

Clogged drain pipe

Dirty water from the clothes is expelled through the drain pipe.

In the long run, a drain pipe may accumulate dirt and debris, which blocks the water flow. 

If the water is not draining from the drain pipe, it will return to the tub, causing the overflow.

It might be a reason for the display of the FE error code. 

To fix this issue, you must unclog the drain pipe to enhance the draining.

A faulty water level pressure switch

You can find the pressure switch at the top of your washer.

It monitors the water lever of the washer and signals it to the control panel. 

If the water is filled to the desired level, it will shut off the valve to prevent overflow. 

Replace the water level pressure switch if it is damaged.

You can also fix the issue by resetting your LG washer if control panel glitches are causing the error code.

Unplug the washer from the electric outlet.

Wait for 5 to 10 minutes. 

After 10 minutes, plug in the washer. 

The reset is complete.

Check if the error code has disappeared. 

2. Error code LE

When the LE error code is displayed in your LG washer’s control panel, it indicates that your motor is locked.

It also occurs if the hall sensor is damaged. 

Follow the steps to clear the LE error code in your LG dishwasher:

Inspect the rotor of your washer.

A rotor is a part of the rotating mechanism in the washer.

If the rotor is damaged, a washer won’t run as it should, and the motor of it will also get stuck. 

Check the condition of the rotor in your LG washer and replace it if you find it damaged. 

Follow the steps below to replace the rotor:

  • Disconnect the washer from the electric and water supply. To disconnect the water supply, turn off the water supply valve and remove all the water supply lines from the washer.
  • Access the back panel of your washer and disconnect it by removing the screws securing it.
  • You can locate the rotor at the base of the washer’s tub. Disconnect the rotor by unscrewing the bolt connecting the tub shaft and rotor.
  • Disconnect the rotor and check if it is defective.
  • Suppose the teeth of the rotor are stripped. You must replace the rotor completely. 
  • Replace it and detach the back panel.
  • Reconnect the water supply and plug in the washer.
  • Press the start button and check if the LE error code is cleared. 

Check the hall sensor of your LG washer.

A hall sensor is commonly referred to as a rotor position center.

The main purpose of the hall sensor is to determine the rotation speed of the motor.

According to the load of the washing cycle, a hall sensor signals the control unit to maintain the rotation of the drum and motor, preventing the washer from getting off-balanced. 

If the hall sensor becomes defective, a washer motor won’t rotate, resulting in the LE error code in the control panel.

  • To fix this issue, you must replace the hall sensor.
  • Remove the back panel of your washer.
  • Locate the rotor and disconnect it by removing the bolts and screws.
  • You can locate the stator after removing the rotor unit.
  • Loosen the stator by unscrewing the bolts and securing it in a position.
  • Fold the stator to locate the hall sensor.
  • Remove the hall sensor from the washer by disconnecting the wire harness.
  • Check if the hall sensor is damaged.
  • Replace the old hall sensor with the new one and connect it to the wire harness.
  • Reattach the rotor unit and secure the stator with bolts.
  • Reattach the back panel and secure it with screws.
  • Replug the washer with the electric unit and check if the LE error has disappeared. 
  • Try resetting your LG washer if these fixes don’t clear the error code. It will help to clear the error code if minor issues are causing the LE error code. 

3. Error code OE

OE error codes in the LG washer appear when there are draining issues in the washer.

To fix this issue, you must figure out why your washer is not draining. 

To give you an idea, here are some reasons why your LG washer won’t drain properly.

Clogged pump filter

The pump filter is located on the front side of the washer.

It protects the pump from getting clogged with dirt and debris. 

OE error code occurred when the pump filter got clogged.

A clogged pump filter will cause the draining issue. 

Cleaning and unclogging the pump filter can clear the OE error code.

Drain pump issues

A drain pump expels the water from the washer to the drain hose.

Suppose the drain pump is not working.

It won’t pump the water out of the washer, causing draining issues. 

As a result, the OE error code will display in the LG washers control panel. 

To fix the issue, you must replace the drain pump if it seems damaged.

A clogged drain hose

If your washer has draining issues, check if a drain hose might be knicked or clogged.

To fix this issue, check if the drain hose is kinked.

Straightening it will regulate the water flow. 

As a next step, check if it is clogged with dirt and debris. 

Disconnect the drain hose from the washer and run it under the water. Prepare a vinegar solution to run through the hose. A vinegar solution will help to unclog the drain hose. 

Also, check if the drain hose is correctly installed to facilitate smooth water flow during the rinsing cycle. 

Follow the steps mentioned above to solve the draining issues in your washer. And also reset the washer. 

4. Error code dE

If the door is not latched with the washer, it will display the dE error code on the control panel. 

Common causes of dE error code are:

  • A faulty door latch assembly.
  • A spring in the door of the washer is worn out. 
  • The power on or start button in the washer’s control panel is not working. 
  • A lock assembly has a damaged lid lock. 

To fix this issue, replace the defective parts.

Consider resetting your LG washer to clear the minor glitches causing the error code. 

5. Error code CL

If your LG washer is not getting started while displaying the CL code in the control panel, it indicates that the child lock is enabled.ย 

With this, you can understand that the cl code is not an error. 

If the child lock is activated, buttons on the washer’s control panel will not respond to the commands. 

It is useful to prevent the washing machine from getting operated by children accidentally. 

The mindless operation will break the appliance because the washer is sensitive and multi-operational. 

You can clear this error code by deactivating the child lock in your LG washer. 

Locate the child lock button on the control panel.

Press and hold the child lock button for 3 seconds to deactivate it. 

If there is no dedicated button for the child lock feature in your washer, you can deactivate it by pressing the following buttons simultaneously.

  • Temperature + option button 
  • Prewash + super rinsing. 
  • Additional washing + Intensive washing.

If the cl lock is not still deactivated, reset your LG washer.

Resetting it will help the washer to clear the Cl lock.

Also read: How Do I Fix The CL Code On My LG Washer?

6. Error code UB/UE

UB/UE error code displays in the control panel when your LG washer is out of balance.

To clear the error code, you must figure out the cause and solve it as soon as possible.

If a washer is out of balance, it may cause hazards to people operating it. 

Common causes of UB/UE error codes in the LG washer:ย 

  • Your washer is not placed on a leveled surface. 
  • You have overloaded the washer’s tub with heavy clothes. 
  • The clothes are tangled. 

You can fix this issue by following the steps below. 

Balance the washer’s load

If the clothes are tangled and start settling on one side of the washer, it will cause an off-balance. 

To fix this issue, manually detangle the clothes.

While loading clothes in the tub, categorize the clothes to avoid detangling. 

Avoid overloading the washer.

Manually remove some clothes if the washer is stuck displaying the UB error code. 

Loading only one or a few clothes in the washer will cause the washer to get off-balanced. 

Consider referring to the user manual to understand the load capacity of your washer.

It will help you prevent overloading it next time. 

Check if your washer is placed on a leveled surface.

If you have moved the LG washer to the new location, you may have placed it on an unlevel surface.

You can use a level tool to check if your washer is placed on a leveled surface.

If the washer is not placed on a leveled surface, you can adjust the washer’s leg to prevent it from getting off-balanced.

Using a wrench, adjust the legs of the washer.

And if the floor is slippery, use a non-slip pad under the legs to bring balance while operating it.

7. Error code tE

tE error code in the LG washer indicated that the thermistor is faulty.

A thermistor in the washer monitors and regulates the temperature during the washing and rinsing cycle. 

You can clear the error code by following the steps below:

  • Disconnect the power supply from the washer.
  • Wait for 5 to 10 minutes.
  • After 10 minutes, plug the washer into the electric outlet.
  • Press the start button.
  • Locate the spin speed button and press it for 3 seconds until no spin is displayed in the control panel. 

It will help to drain the water and clear the tE error code in the dishwasher.

8. Error code “SUD.”

The SUD error code in the LG washer means that too much SUD is produced in the drum due to excessive detergent, which hinders the washer’s function.

The good part is an LG washer will run the rinse cycle automatically to solve the issue. 

All you have to do is to leave the washer undisturbed until the error code disappears.

Final thoughts

Error codes in the LG washer communicate specific faults. If your LG washer displays a particular error, you must know what it indicates to fix the issue. 

The error code differs based on the brand of the washer. So, consider referring to the user manual to understand what an error code indicates. 

This article discusses 8 common error codes in the LG washer and how you can clear them. Follow the steps mentioned in the article to clear the error codes. Resetting a washer will help to solve the minor control panel issue causing the error codes. 

Seek professional help if you can’t solve the error code, even after taking the necessary steps.

Reference: APPLIANCE STANDARDS AWARENESS PROJECT, LG Official Guide,

Ice Maker Only Makes Crushed Ice: Easy Fix

Written by Jeniffer Smith in Refrigerator,Appliances 

The ice maker can make both crushed and cubed ice. It depends on the selection mode that you select. But if you select the cubed mode and the ice maker gives you crushed ice. Then it can be a big issue.

The ice maker will only make crushed ice if the temperature inside the ice maker might be too low or some ice might get stuck inside the lever behind the tray. Check the temperature, ensure it is set right, remove the ice tray, clean it with warm water, set it back, and try again.

In this article, I will show you the easy-to-fix method that can easily resolve the issue of your ice maker making crushed ice instead of cubed ice. So keep reading.

Why is my ice maker only making crushed ice?

These are some common reasons why your ice maker only makes crushed ice.

1. The ice maker is set to the crushed ice mode

When you buy a new refrigerator, the manufacturer has already set the default mode into the machine.

And in some fridges, the ice maker is set in the default crushed ice mode.

Therefore, every time you tap the ice dispenser switch, it gives you crushed ice.

2. The little tab window behind the ice tray isn’t working properly

When you pull out the ice tray from the ice maker, you can find a little tab window in the back wall of the ice bucket.

It moves up and down and helps make cubed and crushed ice.

If it moves up, you can get crushed ice; if it moves down, it gives cubed ice.

A lever always attaches to it and helps the tab to move.

The tab stays down if you select cubed ice.

But somehow, if the ice gets stuck on it and its window doesn’t come down, it can cause crushed ice.

3. Insufficient water pressure

Three things help an ice maker to work properly.

Water pressure is one of them.

Water pressure helps water to flow inside the ice maker.

If the pressure is insufficient, then enough water does not fill.

And you can get small crushed ice instead of cubes.

4. The shut-off valve issue

The shut-off valve is the main component that helps water to come inside the refrigerator’s ice maker.

If the valve leaks or is clogged with particles, the ice maker does not get enough water to make full-size ice cubes.

And that can be the reason your ice maker only makes crushed ice.

5. The lever is not working properly

If you pull outside the ice tray, you can find a lever, a spindle-type metal wire behind the tray.

It adds to the small little tab that is present on the back wall of the bucket.

The lever moves in a half-path.

When you set the cubed mode, this little lever stays up, and when you set crushed mode, it stays down.

But if the lever stops working because its spring becomes frozen or jammed, it can give crushed ice.

6. The plastic flap is not working

If you look inside the ice tray, you can find a plastic flap inside a big hole at the end of the tray.

The flap opens or closes when you move the lever up and down.

If the ice hole is filled in ice completely, then the lever will be up and helps the ice cube to come out by opening the flap.

The lever stops working if any ice cube gets stuck behind the ice bucket. 

Or starts malfunctioning.

And it can give crushed ice.

7. Freezer temperature is too low

It is one of the common causes why your ice maker makes only crushed ice.

The optimal temperature helps to format the perfect ice cube.

If the refrigerator temperature is too low, the ice will break when it is collected from the ice maker.

And this can be the reason why your ice maker is making crushed ice only.

8. Problem with the refrigerator water filter

The water filter helps in the filtration of water and helps to move water inside the ice maker.

But sometimes, the water filter is clogged, can freeze, or needs to be installed correctly inside the refrigerator.

So that can be the reason for low water pressure, and that’s why your ice maker makes crushed ice.

9. Metal rod does not connect with the solenoid

If you pull out the ice bucket outside, you can find the motor and solenoid behind the bucket.

This solenoid is always connected with a thin metal rod.

If the metal rod does not connect with the solenoid, the plastic flap behind the ice tray will not move, which can make crushed ice.

10. Control panel is not working properly

You can find a control on the outside wall of the refrigerator, above the ice dispenser.

Sometimes the control panel does not work properly, that’s why it sends the wrong information to the ice maker.

It can be the reason why your ice maker makes only crushed ice.

How do I stop my ice maker from crushing ice?

So, until now, you have just known why the ice maker only makes crushed ice.

Now you will know how to fix it.

So, let’s get into the topic.

1. Select the right mode of selection

Before doing anything, check if you selected the right mode.

Sometimes we make some basic mistake, and the solution is so easy, but still, we call the technician and spend a lot of money on it.

So first, check if you have selected the cubed mode for getting cubed ice.

If you set it to crushed mode, reset it to cubed mode, and only then can you get cubed ice.

If you are still getting crushed ice, the problem lies elsewhere.

2. Reset

Sometimes a simple reset can resolve a big problem.

So before going to any other solution, reset the ice maker.

  • To do that, first, open the refrigerator door and pull out the ice maker outside.
  • And then push it inside the same place again.
  • Once done, close the freezer door and set the panel switch in crushed mode, then cubed mode.

Check if you now get cubed ice or not.

3. Check if the ice maker is set to crushed mode

To check if the ice maker is automatically set to crushed mode:

  • First, you should open the refrigerator door.
  • Then, pull out the ice tray outside.
  • Once it is done, look inside the ice bucket.
  • You can see a white float switch that is kept up by default.
  • You should keep the switch down if it is not.
  • Reinstall the ice tray inside the bucket.
  • Now close the fridge and select the cubed mode.

Check if you are getting cubed ice.

If you still can not resolve the problem, look for the next solution.

4. Resolve the issue of the lever located behind the ice tray

If you are getting any sound when the ice dispenser gives you crushed ice, it can be the reason for the lever or lever spring connected to the plastic flap behind the ice tray.

To get assurance, check inside the refrigerator.

If you check correctly, you can find that the sound comes from the little plastic flap on the backside of the ice tray.

The little plastic flap bottom of the ice maker tray moves behind noisily.

First, pull out the ice maker outside the freeze to know more about the issue.

In the backend of the ice maker, you find a thin little wire-like structure lever that can rotate. It rotates in half circular motion.

If the lever’s spring is frozen and the tab on the back wall of the ice bucket is freely moving, that’s why the plastic flap is moving noisily.

Somehow ice got clogged in the middle of the spring, which is why it’s happening.

To resolve the problem, pull out the ice tray outside and rinse the whole assembly with warm water, then the ice will melt.

Now reinstall the whole assembly and check if the ice maker is giving cubed ice.

5. Set the right temperature

The optimal temperature for getting cubed ice is 64.4ยฐF.

If the refrigerator’s temperature is less than optimal, the ice will break during the collection.

The simple way to fix the issue is by raising the temperature to 64.4ยฐF.

6. Connect the metal rod with the solenoid

To fix the issue, first, pull out the ice bucket and look at the bottom of the bucket.

You can see a thin narrow metal rod and move it up and down.

It is connected to the lever.

And there is a plastic tab that does nothing when you move the metal rod.

To know more about the issue, open the refrigerator and select the cubed mode on the panel without closing the refrigerator’s door.

Hold down the “Close door” switch and push the ice dispenser like you want to get cubed ice.

Here, you should hear a somewhat loud click.

If you did not find any loud clicks, look where the rod goes in the back of your freezer.

You can see a white semi-circular shape plastic flap.

Reach in there with a screwdriver or a knife and look if it is moving freely or not.

If it is moving freely, then the issue may be with the solenoid.

So the next step is to remove the ice maker assembly outside the freezer.

  • Unplug the refrigerator and move it away from the wall with someone’s help.
  • Turn the water supply valve off.
  • Take a screwdriver and unscrew the back panel of the fridge.
  • Disconnect the inlet water valve tube with a wrench.
  • Now unscrew the mounting screw.
  • You can now take the solenoid out of the refrigerator.
  • Check if the solenoid is stuck with ice or not. If it is stuck with ice, melt it and reinstall the assembly inside the fridge.

Also, check if a metal rod goes into the solenoid.

If you do not find it, you should buy a new assembly and replace it with the old one.

7. Resolve the water pressure issue

To fix the issue, you should first check the water shut-off valve.

It is located near the kitchen sink.

Check if the water shut-off valve is clogged inside or leaking.

  • To do this, first, disconnect the water supply line.
  • Next, tighten the packing nut of the shut-off valve and then connect the water supply line to check if the shut-off valve is leaking or not. If it leaks, you should install a new water shut-off valve.
  • To install the new valve, first, remove the packing nut, remove the bolts and screws, and install the new valve inside.
  • And if the valve is not leaking, then you follow the above steps, remove the water valve assembly, and check inside if there is anything clogged or blocked. And also clean it.
  • Then reinstall all the parts and check if the issue is resolved now.

8. Replace the water filter

[amalinkspro type=”image-link” asin=”B009PCI2JU” new-window=”true” apilink=”https://www.amazon.com/dp/B009PCI2JU?tag=uhc02-20; img-size=”480,500″ addtocart=”false” nofollow=”true” alt=”GE RPWFE Refrigerator Water Filter | Certified to Reduce Lead, Sulfur, and 50+ Other Impurities | Replace Every 6 Months for Best Results | Pack of 1″ alignment=”aligncenter”]https://m.media-amazon.com/images/I/31bnyAWUHoL._SL500_.jpg[/amalinkspro]

If the water filter is clogged or not set correctly, it causes low water pressure.

To check the condition and fix the issue, follow the steps:

  • First, check the water filter indication light. Is it red, yellow, or green? If it is green, then the water filter works well. If it is yellow, you should order a water filter; if it is red, you should replace it. Once you get the red light, it is time to replace the old filter.
  • The first step is to turn off the power of the ice maker. The location of the ice maker depends on the model and brand. So you can find the model name or location of the filter in the user manual.
  • Now remove the filter by reading your refrigerator’s user manual, and install the new one inside it.
  • And now, power on the ice maker and check if it works properly.

Final words

This article should help you discover why your ice maker only makes crushed ice. I have explained all the possible reasons and their fixes.

Before you disassemble the parts of the ice maker, make sure you check the basics. For instance, the ice maker selected cubed mode, the temperature is appropriate, or the ice maker got enough water pressure.

If you think you cannot handle it yourself, seek professional help by calling a technician or the customer service number.

Also read: 5 Reasons Your Ice Maker Is Not Making Ice (+Fix)

How To Reset The Whirlpool Gold Dishwasher?

Written by Jeniffer Smith in Dishwasher,Appliances 

Reset is the effective solution to most of the glitches that occur in a dishwasher. If your dishwasher is not starting or is stuck mid-cycle, you can reset it. Not sure how to reset it? Let’s learn more about it in the article.

You can reset your Whirlpool gold dishwasher by unplugging it from the electric outlet and waiting for 10 minutes, and replugging it to the electric outlet. To do a soft reset of your dishwasher, press the Heated dry and normal buttons in sequence until you hear a beep sound.

In this article, I will help you understand 3 easy ways to reset your Whirlpool gold dishwasher. You will also understand how to fix the issues if your dishwasher is not working. So, keep reading.

Why should you reset your Whirlpool gold dishwasher? 

A dishwasher is a favorite appliance for almost everyone who loves cooking.

Who doesn’t like a device which saves lots of time and effort? 

Everyone does like such devices.

That said, dishwashers are multi-functional, frequently used, and prone to certain faults and failures.

But the good part is that you can solve most dishwasher issues with a simple reset.

Certain situations are listed below when you must consider resetting your whirlpool gold dishwasher to solve the issue.

Let’s thrive.

1. If the child lock is automatically activated

All the new model whirlpool dishwashers have the child lock feature.

The role of a child lock feature is to lock buttons in the control panel when activated.

And when the child lock feature is activated, opening the dishwasher’s door will be difficult.

While some Whirlpool dishwasher models have a dedicated button for enabling and disabling the child lock feature, not all gold whirlpool dishwashers have buttons for the child lock feature.

In such a case, you can simultaneously press Rinse and Spray options for 3 seconds to activate and deactivate the child lock feature. 

A child lock feature is beneficial if your toddler often runs around the kitchen.

As the dishwasher is a heavy-duty appliance, operating it results in hazards.

When the child lock is activated, even if the child presses the buttons, the dishwasher won’t respond.

But the issue arises when the dishwasher is stuck in the child lock.

Initially, try deactivating it by pressing the rinse and spray buttons to switch it off.

If it doesn’t seem to work, you must reset the dishwasher. 

Often resetting will deactivate the child lock feature. 

2. If your dishwasher is stuck in sleep mode

If the sleep mode is activated, you may reduce the efficiency of your dishwasher.

Sometimes, the dishwasher is stuck in sleep mode, causing trouble. 

In such cases, you can reset your dishwasher to deactivate the sleep mode.

3. If the delay wash option is activated and you can’t switch it off

Another important feature of the dishwasher is the delay wash option.

A delay wash option lets you schedule the washing cycle at your desired time.

The delayed washing time varies based on the model of your dishwasher. 

You cannot start the washing cycle if the delay wash option is activated. 

Sometimes, a dishwasher may get stuck in the delay washing option due to the control panel glitches.

If you are facing the same issue in your dishwasher, a hard reset will help to solve the issue.

4. If the door is not latching properly

The dishwasher’s door latch has an electrical component that signals the control panel if the door is closed properly or it is not. 

In the long run, the electrical component may wear out due to the frequent use preventing the dishwasher from beginning the wash cycle. 

Sometimes, control panel glitches will also miss detect the sensor preventing the dishwasher from starting the wash cycle.

If the door latch is worn out, you must replace it to fix the issue.

If the control panel glitches are causing this issue, a simple reset will help the dishwasher to eliminate the issue.

5. If your dishwasher is running too long than usual

There are several reasons for a dishwasher to run longer than usual, ranging from simple to complex issues.

Some important causes are clogged drain hoses, filters, or blocked air vents.

If they are clogged, the water flow will get hindered, resulting in a longer cycle than usual. 

Other common causes include a faulty heat element, wrong temperature settings, and wrong cycle settings. 

To fix this issue, you must unclog the drain hose and filters if they are causing the issue. 

If it’s the heating element causing the issue, the only solution is to replace it. 

If the wrong temperature and washing cycle settings cause the issue, a hard reset will solve the issue. 

A reset will help fix the glitches causing the wrong wash cycle settings.

6. If your dishwasher is not cleaning efficiently

You will not clean dishes efficiently if the dishwasher’s interior is dirty.

Check if your dishwasher has accumulated mineral build-up and detergent build-up.

If that’s the case, clean it thoroughly with a vinegar-cleaning solution. 

Check if you are loading the dishes properly.

The way you load dishes will affect the quality of cleaning. 

After cleaning the dishwasher, you must reset it for the desirable cleaning. 

7. If your dishwasher is not starting

Check the power supply connections if your dishwasher is not starting.

Without a constant power supply, a dishwasher will have trouble getting started. 

Try resetting your dishwasher to get a constant power supply.

8. If your dishwasher is making loud noises

The reason for the loud noise from the dishwasher may be the worn-out bearing.

A bearing is located inside the drain pump to support the rotation of the rotor. 

If the bearing is rusty or worn out, it will cause a loud noise during the washing cycle. 

Replace the bearing and reset your dishwasher to restore it to good working condition. 

9. If a bad odor comes out of your dishwasher

A dirty filter is the main reason your dishwasher spreads bad odor around the kitchen.

In such a case, you must clean the filter at the dishwasher’s bottom. 

You must also reset your dishwasher after cleaning or replacing the filter. 

Resetting will not solve the issue, but it helps the dishwasher to reboot and re-energize after being dismantled and reassembled.

3 Easy ways to reset your Whirlpool gold dishwasher

Here are the three ways in which you can reset your dishwasher.

Resetting is simple but capable of solving several issues.

Follow the steps below to reset your gold whirlpool dishwasher.

1. Hard reset

A hard reset will reboot your dishwasher, the most effective type of reset that will help solve all the control panel glitches. 

Follow the steps below to hard reset your whirlpool gold dishwasher:

  • Unplug the dishwasher’s power cord from the electric outlet or turn off the circuit breaker if your dishwasher is hardwired.
  • Keep the dishwasher disconnected from the electric outlet for 10 minutes. It is because even after unplugging the dishwasher from the electric outlet, there will be electric charges in the device as it is a heavy-duty appliance. 
  • After 10 minutes, plug in the dishwasher. 

Now the hard reset is complete.

Switch on the start button in the dishwasher and check if the issue is solved.

2. Soft reset

A soft reset doesn’t require you to unplug the dishwasher.

You can perform the soft reset by pressing the two buttons in the control panel. 

Follow the steps below to perform the soft reset in your dishwasher:

  • Check if your dishwasher is plugged in.
  • Locate the Heated dry and Normal buttons in the dishwasher.
  • Press and hold these buttons in the sequence of “Heated dry” and “normal,” “Heated dry,” and “Normal’. 

You will hear the beep sound if the reset is complete.

3. Resetting the control panel of the dishwasher

The control panel is the brain of the dishwasher.

Resetting it will solve the glitches causing the issues. 

Follow the steps below to reset the control panel:

  • Press and hold power off button to switch off the dishwasher. 
  • Unplug the dishwasher from the electric outlet or turn off the circuit breaker.
  • Let it stay disconnected from the power supply for the next 10 minutes.
  • Plug in the dishwasher again and switch it on by pressing the start button.
  • Locate the high-setting option on the control panel.
  • Press and hold the high setting button for 3 seconds to reset the control panel. 

How to run the diagnostic mode on the whirlpool gold dishwasher? 

If you have difficulty with your dishwasher and are unsure what went wrong, you can run the diagnostic mode on the dishwasher.

The diagnostic mode will help to identify the issue if your dishwasher doesn’t start if the control panel button won’t respond if your dishwasher has a water supply issue. 

It also helps to fix the issues in the dishwasher. 

Follow the steps to run diagnostic mode on your dishwasher:

  • Turn on your dishwasher by pressing the start button.
  • Locate high-temperature wash and heated dry buttons on the control panel of your dishwasher.
  • Press the high temperature and heated dry buttons in a sequence. 
  • You have switched on the diagnostic mode on your dishwasher successfully. 

Why did my dishwasher stop working all of a sudden?

So far, we have seen why and how to reset your dishwasher.

Now let’s discuss what problem will cause a dishwasher to stop working. 

1. Power supply issues

If no proper power is supplied to the dishwasher, it might get stuck or won’t start the washing cycle. 

You can solve this issue by checking the circuit breaker to see if the dishwasher is hardwired.

Flip the breaker to switch it off and turn it on again. 

If your dishwasher is plugged into the electric wall outlet, try unplugging and replugging the dishwasher. 

Make sure you plug in the dishwasher in the electric outlet. 

2. Check if the child lock button is switched on

If the child lock is activated, the dishwasher won’t start, as the buttons in the dishwasher’s control panel won’t respond. 

You must deactivate the child lock feature to bring the dishwasher back to working condition. 

Locate the child lock button on the dishwasher’s control panel. Press and hold the button for 3 seconds. 

3. Check if the door latch is working

A door latch not only seals the door with the dishwasher but also contains the sensor which passes the electrical signals to the dishwasher if the door is latched well. 

If the door is not latching properly, it must be due to faults in the latch assembly or the sensor.

To fix this issue, you must replace the door latch assembly. 

When you shut the dishwasher’s door too fast frequently, it will cause damage to the latch assembly.

To prevent this issue, you must be careful while opening and shutting the door. 

4. Control panel issues

A dishwasher’s control panel is like a mini-computer with several buttons controlling several functions. 

If the control panel is faulty, the dishwasher won’t start.

In such a case, you need to inspect the control panel’s faults and repair them. 

Inspect the start switch of the dishwasher.

If it is faulty, you must replace it. 

Check the selector switch in your dishwasher if there is something wrong with the start switch. 

A selector switch monitors the settings and sets the preferred cycle in the dishwasher.

If it is damaged, replace the selector switch.

5. A worn-out thermal fuse

A thermal fuse prevents the control panel from overheating.

A dishwasher with a worn-out thermal fuse won’t let the electricity pass to the control panel to prevent it from getting fire and electrical burnout. 

Check if the thermal fuse is damaged and replace it immediately to fix the issue.

How do I reset my Whirlpool Gold Series water filter?

If you have replaced the water filter in your dishwasher, reset it before starting the new washing cycle. 

Follow the steps below to reset the water filter in your dishwasher: 

Locate the cancel/resume button in the control panel.

Press and hold the button and unplug the dishwasher from the electric outlet. 

After 10 minutes, replug the dishwasher into the electric outlet.

Press the start button and start the preferred washing cycle in the dishwasher.

Final thoughts

Resetting is an effective and important step to solve minor glitches in the dishwasher. But you must not unnecessarily reset your dishwasher as it could damage the appliance. 

Ensure to reset your dishwasher only when the issues I mentioned in the article arise. You can reset your dishwasher if it is stuck in the child lock mode, sleep mode, or delay wash option. 

Follow the 3 easy ways to reset your dishwasher as listed in the article. Consider referring to the user manual to get authentic information regarding resetting your dishwasher.

Related articles:

Reference: Whirlpool Dishwasher manual.

How To Vent A Washing Machine Drain Pipe?

Written by Jeniffer Smith in Washing Machine,Appliances,HVAC 

If you have got a new washing machine for your home, you must vent the machine’s drain pipe. It will prevent leakage and flooding of your basement or laundry. You can either call a professional to fix the vent or do it yourself. 

To vent the drain pipe, bend the top of the drain hose in a U-shape and hook it to the drain hole. The main venting pipe has to be connected to the drain hole. Install an air admittance valve on the drainage pipe to control the air pressure in your system.

This article will help you with a detailed procedure for venting the washing machine drain pipe and other factors to consider, the importance of venting, the cost of venting, etc. 

Is a vent for the washing machine drain pipe necessary?

Venting the washing machine drain pipe allows the air to enter the pipe when the water drains out. 

It prevents the vacuum and makes sure that the water can drain completely. 

If you notice carefully, you will find that the ending side of the washing machine drain hose is connected to a Tee fitting. 

This T fitting is further attached to two different drain hoses with different lengths. 

If you do not vent the drain pipe, the water will not drain properly and will start coming back to your washing machine. 

It can further cause other issues like leakages and floods. 

You will also face issues with the washer.

So, you must vent your drain pipe properly to release the water and prevent floods. 

Things to consider while venting a washing machine drain 

When you think of venting a washing machine drain pipe, you should consider a few factors:

  • Ensure that the drain pipe is correctly installed in the washing machine. It will ensure that the pipe remains tight and does not cause any problems or damage. 
  • Use a good venting system that is compatible with your washing machine. 
  • Always use a sponge or clean cloth to clean the inside of the pipe after every use. It will reduce the formation of dirt and filth, which can further block the pipe. 
  • Avoid harsh chemicals in the drain. That can damage the pipe. 
  • Check the vent regularly for blockages. It will prevent leaks, floods, and damage to the machine. 
  • Avoid overuse of detergent. 

How to vent a washing machine drain pipe?

Things needed:

  • A valve for air admittance or AAV – The valve controls the air pressure when you drain the bad water. You can install it above the P-trap, which traps water and blocks the sewer gas. 
  • Inlet valve for water – The water inlet valve helps hold the hot and cold water until they are released after you turn on the machine.
  • One-way valve or Solenoid valve – It helps open the obstacle, transfers power, and supports the water entry valve. Once you turn it on, you can regulate the water temperature by alternating between the cold and hot settings on the machine.
  • Pump hoses – Blue and red hoses in the water entry valve are for cold and hot temperatures. Use valve hoses in the same color to connect the valve on the washing machine’s rear. You can also use these hoses as a water conduit while washing.
  • Disposal house – It is a drain pipe. You can change it by using a longer drain pipe if needed.
  • Slack locks – These locks maintain the stability of the drain hoses, wires, and valve hoses which sometimes get separated due to the machine’s vibration. 
  • Dryer cord – The dryer cord helps connect the four wires – red, green, black, and white – to the primary power source. These wires control the timer, sensor, and other features. The cord divides the voltages to lower the level. Washing machines use lots of electricity, and lowering the level can prevent electric shock and fire.
  • Breathing hose – It is for adequate air so that the pipes stay dry and send the vapor out of the outlet. 
  • Standpipe – It is a horizontal pipe from the drain to the washer. It is angled at ยผ inch per foot toward the drain. 
  • Vent pipe – It is a straight pipe that helps to vent the sewer gasses. It is vented through the roof.  
  • P-trap – It ensures that the water does not remain stagnant and creates a seal to sew the gasses to prevent them from entering the room. 

Step 1

Your first job will be to diagnose the problem due to the absence of the washing machine’s drain pipe vent. 

If you start working without looking out for the issue, you will be tearing out the drywall to find out that you already have a drain vent installed in the wall. 

Check the attic or roofline and see if any PVC pipe has been installed. 

It works as the laundry room’s vent. 

So, you can easily find the current drain vent unless you have an air admittance valve or AAV in the wall. 

Check for blockages too. 

Step 2

Disconnect the washing machine and the dryer. 

Since you have to tear the drywall, you must clear the surrounding area for work. 

If you are working around the dryer outlet, flip the breaker and turn it off. 

You should keep water and electricity away from each other. 

Step 3

Once you have removed the drywall, consider thinking about what exactly you should do. 

If you already have an air admittance valve and your washing machine is still not working properly, check for the AAV’s proper functionality. 

These valves can give out 20,000 cycles every 20 years. 

Step 4

Find the water inlet valve and use the red and blue cords to connect them to the back of the washing machine. 

Fasten the filter to the end of the drain hose with the help of waterproof adhesive tape.

The washing machine will have a drain hose by default. 

Step 5

Bend the hose’s tip to a U-shape before connecting it to the drain hole next to the water inflow valve. 

Now, connect the primary ventilation pipe to the drain hole. 

Step 6

Install an AAV on the drainage pipe if there is no drain vent. 

The AAV has to be at least 4 inches above the washing machine drain connection or the P-trap level. 

The AAV will help regulate the air pressure while draining. 

Step 7

Once you have fixed everything, test the machine with water. 

Turn it on with a full cycle and let the water fill and drain. 

Once you have confirmed the operation, remove the machine and cover the hole in the wall. 

You can also install a wall vent near the AAV so that the room’s air can get pulled out of the system. 

Step 8

Re-connect the wires and plug back the washer and the dryer. 

How to vent the dryer alone?

If the dryer of your machine is separate from it, you will have to vent the dryer alone. 

Here are the steps:

  • Turn off your dryer for safety purposes. 
  • Find the vent hole located along the lower back portion of the dryer. 
  • Install the ventilation hose that connects the dryer to the main vent. 
  • Install a 4-wire dryer cord by connecting the cables accordingly with the colors. 
  • Use a wet fabric to test whether the dryer works and drain it.

The Do’s and Don’ts while venting a washing machine drain pipe

While venting a washing machine drain pipe, you must follow some guidelines and avoid doing certain things. 

Here is a list of the do’s and don’ts while venting the washing machine drain pipe. 

Do’s

  • Clean the filter screen of the washing machine to avoid clogging and blockage. The screen is where the drainage hose is attached. 
  • Keep the washing machine on a plank about 3 inches above the ground to avoid electric shocks when the floor is wet. 
  • Check for the pipes for damages before doing any laundry work. 
  • Cover the valves with a box or a frame to avoid children from detaching the hoses. 

Don’ts 

  • Do not drain the water if the vent is in bad condition. 
  • Do not use any incompatible pipes. Narrower pipes will cause hydraulic pressure, whereas wider pipes will start flooding. Use a pipe measuring only 3-6 inches wide. 
  • Do not approach the work without any professional guidance. Otherwise, you will face issues whose solutions could be unknown and expensive.

Does the washing machine drain hose need air?

If the drain hose of your washing machine is continuously draining water, the reason could be some blockage in the hose. 

If you find any such thing in your washing machine, you must have a vent to let in air for circulation. 

There are a few tips for doing it:

  • Remove the drain hose from your washing machine and keep it in a sink or bucket. 
  • Use a plunger to penetrate air forcefully through the hose and the washing machine. 
  • Now separate the drain hose from the machine and blow it into it. It will push air through the hose and the machine. 
  • Pour water into the washing machine and disconnect the drain hose quickly. 
  • The water running in the hose will push the air through the hose. 

What is the code for the washing machine drain?

Before you fix the drainage system of your washing machine, you must know the code for the washing machine drain pipes. 

The code tells you how the washing machine will ventilate the water used during the cycle. 

When you think of fixing the machine’s drain pipe, there are certain standard codes that you need to use for every work.

The codes also include the drain pipe of your washing machine. 

The drain pipe for a washing machine has to be around 2 inches in diameter. 

It is the standard size for most drains, so it will be easy to find the pipe for replacement. 

During the installation, install the drain pipe for your washing machine so that it slopes downward at the rate of ยผ inch per foot. 

It will ensure that the water drains properly out of the pipe and gets into the sewer or septic system. 

You must also install the drain pipe with a P-trap so the water coming back can be caught in the trap instead of overflowing. 

How can you prevent overflow of the washing machine?

There are other ways to prevent water from overflowing from your washing machine and keep the pipe free of debris or lint. 

However, venting is mandatory. 

Here are a few ways to prevent overflowing:

  • You can use a garment or a lint bag to prevent the excess buildup of lint inside the drain pipes.
  • Maintain ยฝ inch distance between the drain pipe and the discharge hose for adequate drainage. 
  • Use good detergents to avoid the buildup of soap remains. 
  • Clean the hoses and drain pipe regularly. 

How to clean a washing machine drain pipe?

Some people are unfamiliar with the right guide to clearing a washing machine drain pipe. 

Clearing the drain pipes often will prevent flooding and leakages. 

You can follow the following methods to clear your machine’s drain pipe. The steps are simple and easy to perform. 

Method 1

  • Unplug the washer from the power outlet and turn off the water supplies. 
  • Check whether the water tub is empty or not. If water is left, empty it and get a bucket to avoid flooding the area. 
  • Locate the drain pipe from the machine. It will be attached to the back of the washer.
  • You will find screws or a cap to unscrew and open the pipe. 
  • Take a plunger to clean the clogs. You can also use other drain-clearing tools to clean the pipe. 
  • Put the cap back and pour water to confirm the pipe is clear. 
  • Turn the washer on and run clean, warm water and a readymade cleaning product like baking soda or white vinegar. It will clean the pipe more. 

Method 2

You will lift the washer to clear the drain pipe in this method. 

Unplug the washer. 

  • Tilt the washer back to access the bottom of the front panel. You can take someone’s help too. 
  • When the panel is off, find the two hoses near the bottom of the washer. 
  • You will find the hoses connected to the drainage pump. You need to remove them before you continue working further.
  • Once you have removed the hoses, you will see bolts holding the washer. Remove the bolt and lift the washer. 
  • Once the drain pipe is visible, check if there is any dirt, lint, or debris blocking the pipe. Use a brush or vacuum cleaner to remove the dirt.  
  • Once you have cleared everything, put the washer, the hoses, and the bolts back in their positions. 

How much will it cost for the drain pipes?

The cost of the drain pipe depends on your requirements. 

If you want to install or replace the drain pipes, it will cost around $230 to $1,140. 

The building permit will cost around $30 to $150. 

If you want to replace the whole washing machine, it will cost around $350 to $1,200, based on the size you need. 

When should I call a professional?

If you hear noises from your washing machine, smell a bad odor, or see water coming out, you need to contact a professional plumber. 

Taking care of problems immediately will save money and stop the problem from worsening. 

The washing machine will need extra plumbing and cleaning of the drain lines. 

Fixing such things is quite average or confusing for house owners. 

So, calling a professional to fix these things is safe.

Final thoughts

It would be great to vent a washing machine drain pipe, as it will prevent leakages and flooding. 

To vent the washing machine drain pipe, bend the tip of the drain hose in a U-shape, and hook it to the drain hole beside the water inlet valve. 

The main ventilating pipe must remain connected to the drain hole. 

You can install an air admittance valve or AAV on the drainage pipe to control the air pressure in the system. 

Once you have done everything, test the machine’s drainage by pouring water and then turning on the machine. 

Clean the pipes regularly to avoid further clogging and overflow of the water. 

Related Articles

FAQs

What should be the length of the washer drain pipe?

If you use a 4-foot pipe, you can use it for 4 feet in length. 

If you want to vent a pipe 2 inches in diameter, make sure that the pipe is 4 inches long. 

If you want to vent a larger pipe, like a 10 to 12-gallon tank, vent the entire pipe. 

How high should a vent be?

The vent for your washer should be around 24 to 40 inches higher. 

It will make sure that the air pressure is under control. 

Besides, the pressure of the evaporation of the bad water is required to empty and unclog the pipes. 

How long does a vent last?

If the installation processes are followed properly, the vent can last around 12 years. 

You cannot stop the drain damage because you will use them frequently. But, you can increase the lifespan with sufficient care.

Reference:ย GE washer front load user manual,ย LG Official Guide,ย Kenmore User manual, Maytag Front Load Washing Machine Official Troubleshooting Guide.

8 Reasons Your Keurig Is Flashing Lights (+Fix)

Written by Jeniffer Smith in Coffee Maker,Appliances 

Keurig is the creative invention to enjoy a flavourful cup of coffee and other drinks in just a click. It is the best machine for preparing a tasty cup of coffee. But if your Keurig stops amid the brewing cycle with the flashing lights, you are at the right place.

A red light flashing indicates that your Keurig coffee maker has accumulated dirt and needs a descaling. To fix this issue, you must descale the machine with the cleaning solution. Sometimes you may notice a blue light flashing when the water reservoir is low; refill the water to fix that.

This article will discuss the causes of flashing lights and the steps to fix the issue. So, keep reading.

How does Keurig work? 

Keurig coffee machines come with K-cups, which hold different flavors.

It enables individuals to choose their favorite flavors of coffee instead of boring ones.

K-cups have coffee pods to brew different flavors of coffee and dedicated pods for tea and chocolate drinks. 

They are disposable cups with foil sealing at the top.

Inside the K-cups, ground coffee and filter are added. 

They are sealed after expelling the oxygen completely.

As the K-cups are devoid of oxygen, it retains the flavor to produce high-quality coffee by reducing exposure to moisture. 

It is not to deny that Keurig is the best choice to make coffee faster with just a click.

If you are a regular user of Keurig, it is well known that when K-cups are attached to the brewer, it makes a hole in the cup to pour the hot water to reach the ground coffee.

Through another hole, a beverage travels to the filter. 

And finally, the coffee pours into your cup through the last hole made in the K-cup. 

Unlike drip coffee, Keurig has a water reservoir and has hot water ready almost all the time.

It is the feature that makes the Keurig the fastest coffee brewer machine.

Why is my Keurig flashing lights? (+Quick fix)

Seeing the red, blue, and other lights blowing in the Keurig is normal.

But if they are frequently flashing, it may be due to several causes.

Here are 8 reasons why lights are flashing in your Keurig, and you can fix them. 

1. Your Keurig has accumulated dirt

As Keurig coffee makers are used daily, they are prone to dirt and debris accumulation.

A Keurig descaling red light will start flashing if the dirt accumulation exceeds the limits.

When you notice a red light flashing frequently, you must understand that your device needs immediate descaling.

The most common reason for the dirt accumulation on the Keurig is the usage of hard water to brew the coffee.

The other common reason includes the deposition of the ground coffee in the machine when left uncleaned for a longer time. 

At times, dirt particles are deposited in the interior of the Keurig, which will prevent the machine from starting as those dirt particles clog the machine. 

You can eliminate this issue by cleaning the Keurig coffee maker at least once weekly. 

Follow the steps below to descale your Keurig coffee maker:

  • Begin by disconnecting the Keurig from the electric supply by removing the power cord from the electric outlet.
  • Detach all the removable parts from the Keurig. You can remove the coffee maker’s K-cup holder, lid, water reservoir, and mug.
  • You can prepare a cleaning solution with white vinegar. Mix the white vinegar with water in a bowl and soak all the parts in the cleaning solution for 30 minutes. You can also purchase a Keurig descaling solution for effective cleaning.
  • After 30 minutes, clean all the removable parts with a brush and dry them completely.
  • Take a clean cotton cloth and dip it in soapy water. Wipe the machine’s exterior surface with this soft cloth.
  • Attach all the parts to the machine and switch it on after attaching the power cord to the electric outlet.
  • Fill the water reservoir with the vinegar up to half full and fill the remaining half with water.
  • Begin the brewing cycle without attaching the K-cup.
  • Keep repeating the brewing cycle until the water reservoir filled with the vinegar is empty. Doing this will remove the dirt and deposition from the machine. 
  • Begin the second cycle by filling the reservoir with water to remove the vinegar residue. 

Now your Keurig is descaled successfully.

You make the coffee as usual. 

2. Check if the reusable K-cups are sealed tight

[amalinkspro type=”image-link” asin=”B007TJGZ54″ new-window=”true” apilink=”https://www.amazon.com/dp/B007TJGZ54?tag=uhc02-20; img-size=”500,500″ addtocart=”false” nofollow=”true” alt=”Green Mountain Coffee Roasters Breakfast Blend Single-Serve Keurig K-Cup Pods, Light Roast Coffee, 24 Count (Pack of 4)” alignment=”aligncenter”]https://m.media-amazon.com/images/I/41a9cBdpiuL._SL500_.jpg[/amalinkspro]

A red light will frequently flash if you use reusable K-cups instead of regular K-cups and you excessively tighten the cup.

It is because you may have sealed the cup too tight.

Doing this will cause a lump in the ground coffee, making the reservoir water hard to pass.

A Keurig will recognize this as a clog in the pipes, resulting in the flashing red light. 

To fix this issue, next time you use reusable K-cups, you must only fill the ground coffee up to the mark and avoid twisting it too tight.

Following this, make the water pass the K-cups without any hindrance. 

3. Check the exit needle

The bump in the K-cup may clog the exit needle.

If the exit needle is clogged, it will block the water flow. 

This blockage will make it difficult to brew hot drinks and coffee. 

To fix this issue, you must clear the clog in the exit needle. 

Follow the steps below to clean the exit needle:

  • Unplug the Keurig from the electric outlet to prevent yourself from the electric shocks.
  • Disconnect the pod holder from the Keurig. You need to lift the handle and twist the pod holder to remove it from the machine.
  • The next step is to separate the funnel from the top of the pod holder. The funnel is the part that comes below the pod holder.
  • Twist the pod holder firmly to separate the funnel from the top piece. 
  • If you find it difficult to separate them, you can soak them in hot water to disconnect them easily.
  • You can locate the needle by flipping the pod holder upright. 
  • Keep the paper clip handy to clean the tube. Insert the paper clip into the tube and clean it for 30 -60 seconds. Remove all the clogs in the exit needle by moving the paper clip around.
  • Keep the pod holder and funnel under the running water to rinse them thoroughly. Grab them in your hands and rinse them in the tap water.
  • Wipe the pod holder and the funnel with the cotton cloth. Please keep them open to get rid of all the moisture.
  • Reconnect the pod holder and funnel together by twisting them tight.
  • Position it on the machine and align them with the tabs.
  • Plug the Keurig into the electric outlet. Run the brewing cycle with plain water.

4. The water reservoir of Keurig is low

The Keurig requires at least a minimum amount of water in the water reservoir to brew the coffee.

If the water is low in the reservoir, a blue light will start flashing, and the brewing cycle won’t start. 

It is simple to fix this issue.

All you need to do is fill the reservoir with fresh water.

If your machine is still flashing blue, switch it on and off and check if the blue light stopped flashing. 

5. A mispositioned water filter

If the lights are flashing in the Keurig, another reason would be a water filter not installed correctly.

Sometimes, a Keurig will not start if the water filter is misaligned. 

Also, you must change the water filter every two months.

Follow the steps below to replace the water filter correctly:

  • Begin by disconnecting the power supply from the Keurig coffee maker.
  • The water filter is located on the left side in most Keurig models. You can access the water filter only after removing the top of the machine.
  • Open the top of the Keurig machine and access the water reservoir.
  • You can find the filter unit next to the water reservoir.
  • Pull the filter unit out by removing the water reservoir holder.
  • Separate the filter holder and the filter by twisting the tabs holding the filter with the filter holder.
  • Discard the used filter in the trash can.
  • Buy the new filter depending on the model of your Keurig.
  • You must not attach the filter immediately after the purchase. Soak the filters in the bowl of water for 10 to 15 minutes.
  • After soaking the filter in a water bowl, rinse it in the running water for 60 seconds.
  • Rinse the filter holder in the running water. A filter holder will have a mesh, and rinsing it will remove dirt and dust accumulation.
  • Attach the filter and the filter holder by aligning them with the tabs.
  • Set the remainder for replacement of the water filter after 2 months. Go to settings, and choose a water filter reminder. Select the enable option and set the time duration for 2 months.
  • Reattach the water filter unit to the water reservoir.
  • Close the top of the machine and connect the machine to the power supply. Check if the flashing of lights has stopped. 

6. Check the magnet inside the water reservoir

If your Keurig is flashing red continuously, it may be due to the mispositioned magnet inside the water reservoir.

Due to the vibration caused in the machine while brewing the coffee, a magnet may move from its position. 

A Keurig will stop amidst the brewing cycle if the magnet is mispositioned. 

You can fix this issue by following the steps below:

  • Disconnect the power supply from the device.
  • Disconnect the water reservoir from the machine by pushing it in a vertical position.
  • The magnet is black and positioned in the water reservoir’s middle.
  • Remove the lid of the water reservoir and adjust the position of the water reservoir manually.
  • Lock the magnet in its position firmly.
  • Now the red light will stop flashing. 

7. Check if the heat-up mode is activated on your Keurig

If the heat-up mode is activated and your Keurig is stuck in a heat-up mode, the red light will start flashing. 

To fix this issue, you must get the machine out of the heat-up mode. 

Follow the steps below to reset the heat-up mode in your Keurig machine: 

  • Switch off your Keurig machine and disconnect the power cord from the electric outlet.
  • Detach the water reservoir from the machine. 
  • Let it stay disconnected from the power supply for 5 minutes.
  • Repeat the process.
  • Reattach the water reservoir to the machine.
  • Plug in the machine and long-press the menu button.
  • Now your machine will be free of heat-up mode. 

8. The flashing of frother lights in the Keurig

If you try to froth the milk while the coffee is brewing, lights will start flashing because you can froth the milk only after the brewing cycle. 

Sometimes all the lights at the base will start flashing for the following reasons:

  • Check if the milk frother base is attached firmly to the machine. 
  • Check if the frother holds the whisk firmly.
  • Check if the milk frother is not overloaded and underloaded. Either of the situations will cause the flashing of lights. 

You can fix this issue by firmly attaching the machine’s whisk and milk froth base. 

Load the milk in the froth only up to the marked level and avoid overloading it.

How do you reset the blinking descale light on a Keurig supreme?

When the descaling light blinks in your Keurig machine, it communicates that it needs a descale. 

Follow the steps I mentioned earlier to descale the Keurig coffee machine. 

After descaling, you must simultaneously press the 8oz and 10oz buttons for 5 seconds to reset the blinking descaling light.

How long do Keurigs usually last?

The lifespan of Keurig depends on several factors. One such important factor is how often you use the Keurig. 

If you brew 5 to 6 cups daily, a Keurig will last up to 3 to 5 years.

If taken properly, the lifespan of Keurig will increase. 

To use the Keurig for a long period, you must clean and maintain it regularly.

Final thoughts

If the lights frequently flash in your Keurig, it may be due to the causes mentioned in the article. Figure out the cause and follow the step-by-step process to fix the issue. A red light flashes when your machine is accumulated with dirt and debris. To fix the issue, you need to descale the Keurig with the vinegar solution and reset the flashing light.

Follow the steps mentioned in the article to descale your machine. The water filter in the water reservoir is trapped with waste in the long run. So, changing the water filter once every 2 months is important.

You can replace the water filter by following the steps mentioned in the article. You can also expand the lifespan of a Keurig by cleaning it regularly. While using the Keurig, ensure you follow the instructions mentioned in the owner’s manual to increase efficiency.

Reference: Keurig Official Manual.

10 Reasons Your Whirlpool Dishwasher Not Spraying (+Fix)

Written by Jeniffer Smith in Dishwasher,Appliances 

A whirlpool dishwasher is among the best dishwashers that can make your life easy in case of washing dishes. It sprays the soapy water around the dishwasher and makes your dishes crystal clean. But it can suddenly stop working and stop spraying water inside the dishwasher.

If your Whirlpool dishwasher is not spraying water, there could be problems with the water supply, clogging of the circulation pump, a broken or clogged spray arm, or even a damaged or clogged water inlet valve. To fix the issue, you need to check each of these parts and clean or replace them.

In this article, I am going deep down into why your Whirlpool dishwasher is not spraying, and I will also discuss the solutions. So, keep reading.

Why is my Whirlpool dishwasher not spraying?

Here I will share with you 10 common reasons why your Whirlpool dishwasher is not spraying.

1. Circulation pump issues

A circulation pump is one important component that helps spread water inside the dishwasher.

With the help of a pump motor and impeller, it pumps the soapy water inside the dishwasher and sprays it through the spray arms.

The circulation pump is located bottom side of the dishwasher, under the spray arm.

 But sometimes the circulation pump stops working and water stop spraying inside.

 There can be many reasons why the circulation pump stops working.

The first reason can be the circulation pump is blocked.

Sometimes food particles, debris, or hair particles move through the spraying water and get stuck into the circulation pump.

And it resists the movement of the circulation pump. 

The second reason may be that it becomes faulty after being used for a long time.

That’s why it’s not able to pump the water.

How to fix it?

To fix these issues, first, you should know what happened to the circulation pump.

For this, you should follow the direction below.

Before doing that, disconnect the dishwasher from the power supply.

  • First, you will need to remove the bottom dish rack, the bottom spray arm, and the part connected to the spray arm.
  • Once it is done, remove the filter and get access to the circulation pump, which is on the pump’s outer side.
  • Check the blades to see if they are moving smoothly without any resistance.
  • If not, you should check behind the pump blades and remove the clogged particles.
  • If you do not find any particles, then it may be the circulation pump has become faulty. You should then replace it with a new one.

2. Clogged spray arms

Spray arms are long narrow plastics that look like ”arms” that help in water spraying around the dishwasher and washing the dishes.

There can be two or three spray arms present in a dishwasher.

Mostly you can find one under the bottom dish rack and over the circulation pump.

It is long, and its length is the same as the dishwasher’s width.

There have small pores in the spray arm that help in spreading water inside the dishwasher.

But food particles, debris, and dirt can somehow occupy the pores and get stuck inside them.

And that can be one of the reasons why the dishwasher might not be spraying water.

And the other reason may be the spray arms are broken.

How to fix it?

You should access the bottom spray arm to check and resolve the issue. 

And to do this, you should follow the below steps.

  • The first step is to remove the dish racks and get access to the spray arm.
  • Once you get the spray arm, remove the bolts and screws and bring the arm outside the dishwasher.
  • Then clean the pores properly. If the pores are too clogged, or the spray arm is broken from overloading the dishwasher, you should replace it with a new one.
  • You must pull the lower spray arm and get it out of the dishwasher.
  • Now, get the new spray arm and push it down in place of the old one.
  • Once you hear a click sound, it means that the spray arm is attached. You can rotate it to check if it is working properly.
  • To get access to the upper one, remove the upper rack and remove the water supply hose.
  • Now, disconnect the spray arm and place the new one. Spin it to ensure it is working properly.

3. Overloaded dishwasher

Sometimes you overload the racks of the dishwasher to save water or electricity.

As you do it, the height of the dishes stops the spraying of water inside the dishwashers.

It blocks the holes and clogs up the holes of spray arms with food or dirt particles sticking on the plates or dishes.

And it can be one of the reasons why your Whirlpool dishwasher might not spray water.

How to fix it?

To fix the issue, ensure you are loading limited dishes as per the space inside the dishwasher.

Do not load too many dishes at once.

4. Water inlet valve issues

The water inlet valve is directly connected to the home water supply.

It controls the water flow into the dishwater.

The water inlet valve shuts and opens as needed to ensure sufficient water availability.

The valve also restricts the overflowing or flooding of water into the dishwasher.

You should check the water inlet valve once if your Whirlpool dishwasher is not spraying water.

As the water inlet valve is connected to the hose pipe or the home water supply, it can get clogged with food particles, debris, or any other particle contaminated with the home water.

And day by day, more particles add to it, becoming dense, and finally, it stops water from flowing.

And the other reason might be that your water inlet valve is burned out from overusing or short circuits.

How to fix it?

  • Disconnect the dishwasher from the power and water supply.
  • Remove the outer and inner control panels.
  • Then remove the bottom access panel by removing the screws in it.
  • Once done, you can find the water inlet valve is connected to the hose of the home water supply.
  • Disconnect the water supply line from the water inlet valve and also remove the screws that hold the water inlet valve.
  • Pull the water inlet valve and disconnect the wires.
  • Remove the round brass ring and clean the valve.
  • Check if you smell burns or can see the smoke. If it smells, congrats, you have to replace it with a new one.

5. Water supply valve issues

The water supply valve is the main component that controls the flow of water from your home’s tank to the dishwasher.

If the dishwasher is powered on and you can hear the sound of the machine but not any water sound, then you should check your home’s water supply valve instead of the machine.

There have many reasons why your water supply valve is not working.

First, the valve may be turned off or not set properly.

Second, the valve is clogged, and the pressure needs to be set properly, or it may leak.

How to fix it?

To fix the issue, observe the water supply valve closely.

To do that, you can follow the below steps.

  • The first thing you should check is if the water supply valve is leaking or not. If yes, you should tighten the nut of the water supply valve. To do this, you need just a wrench.
  • After tightening the valve, if it is still leaking, you should replace the water supply valve with a new one.
  • To replace the water supply valve, you first have to shut off your home’s main water supply line.
  • Then, lose the screws using a wrench and rotate the water supply assembly 3-4 times.
  • Once it loses, pull off the assembly.
  • Next, unscrew the nut using the same wrench.
  • You can install the new valve by replacing it with the old one.
  • When you pull out the old water supply valve, check if there are any particles clogged inside the valve.
  • If you find any particles and dirt, clean them.
  • The next step is setting the valve with the proper pressure, so water can flow inside the dishwasher easily.

6. Wash Impeller issues

The wash impeller forces the water so that it sprays through the spray arm inside the dishwasher and can clean the dishes.

There are two impellers in the dishwasher, one is the drain impeller, and the other is the wash impeller.

The drain impeller is located at the bottom of the dishwasher, while the wash impeller is under the tub.

The drain impeller drains water through the pipe into the drain line.

And the wash impeller pumps the soapy water inside the dishwasher to clean the dishes.

If the wash impeller is damaged or clogged, it stops working and won’t spray water into the dishwasher.

How to fix it?

To fix the wash impeller, you should follow the steps:

  • First, make sure you disconnect the power supply line and water supply line.
  • Then remove the racks.
  • Once done, remove the spray arm and filters one by one.
  • Then unthread the pump cover.
  • Now you can access the circulation pump, and near the pump, you can find the wash impeller.
  • Once it is accessed, check if there have any clogs inside the impeller and clean it.
  • After cleaning, if it is still not working, you may damage the impeller from long use.

Then you should replace the impeller and install a new one.

7. Clogged chopper blade

The chopper blade is a multitasker component that helps wash the dishes, spray water, and chop the food particles and debris into small parts that can move easily outside the dishwasher.

But if the chopper blade clogs, it stops working, and it can cause your dishwasher not to spray.

How to fix it?

To fix the issues, you should follow the steps.

Before starting, make sure you turn off the power supply.

  • First, remove all the dish racks.
  • Remove the bottom spray arm.
  • Now unscrew the cover under the spray arm and filter assembly and remove it.
  • Then remove the foreign object protector.
  • Remove the pump inlet protector.
  • Now you will get access to the chopper blade.
  • Check if any food particles or dirt are clogged on it and clean it.
  • If you smell any burn, it is a sign that the blade is damaged.
  • Using a screw to pull out the sharp chopper assembly to replace the blade.
  • Now install a new food chopper assembly there based on the dishwasher model.

8. Float switch problem

The float switch is located at the bottom of the dishwasher tub.

It helps to prevent the overflow of water inside the dishwasher.

The float switch will turn off when the water overflows inside the dishwasher and stop the water flow.

That is how it works.

But what happens if the float switch doesn’t work properly?

What happens if it becomes faulty?

If there is no water left in the dishwasher, then the float switch assumes that it is flooded and the switch is off, and that’s why water spraying stops.

How to fix it?

There is no other easy fix than replacing the float switch.

Make sure you disconnect the electricity before following the steps.

  • Open the dishwasher door.
  • Remove all the screws using a screwdriver.
  • Now pull the outerdoor pannel.
  • Remove the screws of the access panel and pull it outside.
  • Once it is done, remove the left locking tab on the float switch and open the left side cover.
  • Then disconnect all the wires.
  • The next step, remove the left locking tab and open the left side.
  • Remove the old float switch and install a new one inside it.
  • Reassemble all the parts and try using the dishwasher.

9. Controller board not working properly

The electronic control board manages the dishwasher’s working like washing, drying, and draining.

But somehow, the controller board can be damaged, which can delay the cycle, and the dishwasher can stop spraying.

How to fix it?

For this, you should replace the controller board with a new one.

To do this, you can follow these steps.

  • The first and most important step is disconnecting the electricity from the dishwasher.
  • Open the dishwasher door.
  • Use the screwdriver to remove all the screws.
  • Now pull out the control board panel with the outer door panel.
  • Disconnect all the wires from the controller board.
  • Now pull out the controller board outside the dishwasher and replace it with another new controller board.
  • Reassemble the parts and check if the issue is fixed.

10. Damaged pump motor

If you have already checked all the previous reasons and fixed them and still the dishwasher is not working, it can be the problem with the motor pump.

The motor pump is the engine of the dishwasher.

The entire dishwasher works with the help of the motor.

The motor pump helps the controller pump rotate and spray the water inside the dishwasher.

But if the motor pump gets clogged or stops working, the water will not spray inside the dishwasher.

The motor pump is located at the bottom of the dishwasher and connected to the circulation pump.

How to fix it?

To fix this issue, you should access the motor.

  • Firstly you should disconnect the power and water supply of the dishwasher.
  • Next, you should open the window of the dishwasher and remove the upper and bottom dish racks.
  • Once done, remove the bottom spray arm, upper spray tool, and the two filters.
  • Now remove the bottom access panel.
  • Once it is done, disconnect the water supply line from the water inlet valve. And also, disconnect the wires.
  • Now rotate the water inlet valve and remove it.
  • Now push the pump and the motor up to release it from the dishwasher.
  • Now go inside the dishwasher and disconnect the wires from the circulation pump assembly. Now bring it outside.
  • Check the circulation pump motor assembly to see if anything gets stuck into the pump motor. If you do not find anything, it can signify a damaged motor.
  • Now you should replace it. You can replace it on your own or call a technician.

Final words

This article has all the possible reasons why your Whirlpool dishwasher might not spray water. Inspect the dishwasher thoroughly and find out the exact problem so you can fix it.

Ensure you disconnect the power supply whenever you check the dishwasher for safety. And I suggest you clean your dishwasher once a month. And if you can not resolve the problem with the dishwasher on your own, seek professional help.

Related articles:

Reference: Whirlpool Dishwasher manual.